View SE5007T_7306065.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 1 of 11 applications ? 5 ghz wlan (ieee802.11a/g/n) ? access points, pcmcia, pc cards features ? 5ghz front end module with pa, lna and t/r switch ? integrated power amplifier enable pin (v en ) ? buffered, temperature compensated power detector ? high and low-linearity mode ? 3% evm, @17dbm, 64 qam, 54 mbps ? 30 db typical gain ? lead free and rohs compliant, halogen free package ? 16 pin 3 mm x 3 mm x 0.6 mm qfn, msl1 ordering information part number package remark SE5007T 16 pin qfn samples SE5007T-r 16 pin qfn tape and reel SE5007T-ek1 evaluation kit standard product description the SE5007T is a 5ghz front end module offering high linear power for wireless lan applications. it incorporates a power detecto r for control of the output power. the SE5007T offers a high level of integration for a simplified design, providing quicker time to market and higher application board production yield. the device integrates the input match, inter-stage match, a temperature compensated, load insensitive power detector with 20db of dynamic range, a 3.8ghz notch filter, a t/r switch and lna. for wireless lan applications, the device meets the requirements of i eee802.11a and delivers approximately 17dbm of linear output power. it also features a low linearity mode control to reduce current consumption at low power modes. the SE5007T integrates the reference voltage generator, allowing for a true 1.8v cmos compatible digital en (enable) function to turn the power amplifier on and off. functional block diagram figure 1: functional block diagram match & filter match bias, enable, detector circuits vcc1,2 en txin c0 c1 ant rx h/l lin det
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 2 of 11 pin out diagram figure 2: SE5007T pin-out diagram pin out description pin no. name description pin no. name description 1 en pa enable 9 vdd lna supply voltage 2 gnd ground 10 gnd ground 3 txin 5ghz tx rf input signal 11 ant 5ghz antenna output 4 gnd ground 12 gnd ground 5 rx 5ghz lna output signal 13 det power detector output 6 gnd ground 14 h/l lin high-low linearity control 7 c0 switch control logic 1 15 vcc1 power stage supply voltage 8 c1 switch control logic 2 16 vcc2 bias, driver stage supply voltage
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 3 of 11 absolute maximum ratings these are stress ratings only. exposure to stresses beyond these maximum ratings for a long period of time may cause permanent damage to, or affect the reliability of the device. avoid operating the device outside the recommended operating conditions defined below. this device is esd sensitive. handling and assembly of this device should be at esd protected workstations. symbol definition min. max. unit v cc1 supply voltage on pin 15 (vcc1) 3.0 4.8 v v dd, v cc2 supply voltage on pins 9, 16 (vdd, vcc2) 3.0 3.6 v en dc input on enable -0.3 3.6 v txin rf input power, rfout into 50 ? match - 12 dbm t stg storage temperature range -40 150 c esd hbm jedec jesd22-a114 all pins antenna pin - 1000 v all other pins - 300 recommended operating conditions symbol parameter min. max. unit v cc1 supply voltage on pin 15 (vcc1) 3.0 4.5 v v dd, v cc2 supply voltage on pins 9, 16 (vdd, vcc2) 3.0 3.6 v t a ambient temperature -40 85 c control logic characteristics conditions: v cc1 = v cc2 = v dd = v paon = v en = 3.3 v, t a = 25 c, as measured on skyworks solutions? SE5007T- ev1 evaluation board, unless otherwise noted. symbol parameter conditions min. typ. max. unit i cc-802.11a supply current, transmit mode p out = 17 dbm, 54 mbps, 64 qam, h/l lin = 3.3v (high linearity mode) - 195 - ma p out = 13 dbm, 54 mbps, 64 qam, h/l lin = 0v (low linearity mode) - 140 - p out = 5 dbm, 54 mbps, 64 qam, h/l lin = 0v (low linearity mode) - 105 - p out = 19 dbm, 54 mbps, 64 qam, h/l lin = 3.3v, vcc1 = 4.0v 220 supply current, receive mode v en = c0 = 0v; c1 = 3.3v 15 v en = c0 = c1 = 0v 0.02 i off supply current v en = 0 v, no rf, c0=c1=0 v measured on vcc, vdd pins - 20 50 a v enh logic high voltage - 1.6 - 3.6 v v enl logic low voltage - -0.3 - 0.3 v i enh input current logic - - 330 400 a
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 4 of 11 symbol parameter conditions min. typ. max. unit high voltage i enl input current logic low voltage - - <1 - a switch logic characteristics conditions: v cc = v en = 3.3 v, t a = 25 c, as measured on skyworks solutions? SE5007T-ek1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. symbol parameter conditions min. typ. max. unit on low loss switch control voltage high state = v ctl_on - v ctl_off 2.8 - 3.6 v off high loss switch control voltage low state = v ctl_off - v ctl_off 0 - 0.3 v c ctl control input capacitance - - - 100 pf i ctl control line current v ctl = v ctl_on - 2 10 ua switch control logic table c0 c1 en hi/l lin ant on off on off tx low linearity on off on on tx high linearity off off off d/c rx bypass off on off d/c rx lna on on on un-supported state
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 5 of 11 ac electrical characteristics transmit characteristics conditions: v cc1 = v cc2 = v dd = v en = c0 = h/l lin = 3.3v, c1 = 0v, t a = 25 c, as measured on skyworks solutions? SE5007T-ev1 evaluation board, unless otherwise noted symbol parameter conditions min. typ. max. unit f l-u frequency range - 4.90 - 5.85 ghz pout output power, high linearity mode h/l lin = 3.3v ofdm 802.11a, 64 qam evm = 3% - 17 - dbm evm = 2% - 15 - vcc1 = 4.0v, 3% evm evm = 3% - 19 - mcs0, ht20, mask compliant - 21 - mcs0, ht40, mask compliant - 20 - output power, low linearity mode h/l lin = 0v ofdm 802.11a, 64 qam, evm = 3% - 13 - mcs0, ht20, mask compliant - 17 - mcs0, ht40, mask compliant - 16 - p 1db output 1db compression point no modulation - 24 - dbm s 11 input return loss p in = -25 dbm - 14 - db s 21 small signal gain, p in = -25dbm high linearity mode 28 31 - db low linearity mode 26 30 - s 21 small signal gain variation gain variation over single 40mhz channel - - 0.5 db gain variation over band -1.5 - 1.5 s 21_3.8 out of band gain gain at 3.8ghz - - 15 db 2f harmonic p out = 17 dbm, ofdm - -50 -42 dbm/mhz 3f - -50 -42 t r , t f rise and fall time - - 0.5 - us stab stability p out = 17 dbm, 54 mbps, 64 qam, vswr = 6:1, all phases all non-harmonically related outputs less than -50 dbc/100 khz rugged- ness tolerance to output load mismatching constant p in equal to p out = 17 dbm at 50ohms, 54 mbps, 64 qam, vswr = 6:1, all phases no damage robust robustness to input power p in = 12dbm, cw, vswr = 6:1, all phases no damage
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 6 of 11 receive characteristics conditions: v cc = c1 = 3.3v, v en = c0 = 0v, t a = 25 ? c, as measured on skyworks solutions? SE5007T-ek1 evaluation board, all unused ports terminat ed with 50 ohms, unless otherwise noted. symbol parameter condition min. typ. max. unit f out frequency range - 4.9 - 5.85 ghz rx insertion loss bypass mode: c0 = c1 = 0v - -5 - db rx gain high gain mode 11 12 - nf noise figure high gain mode - 2.5 - db rx rl input return loss at the antenna port - 12 - db output return loss at rx rf output - 7 - rxip1db input p1db measured at ant port; high gain mode - -5 - dbm lna bypass mode - 10 - rx_2.4int max 2.4ghz interferer amplitude 1 db degradation of ip1db - -10 -7 dbm t on/off t/r on/off switching speed c0, c1 (50%) to rf output (10% or 90%) - 300 - nsec
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 7 of 11 power detector characteristics conditions: v cc = v en =c0 = 3.3v, c1 = 0v, f = 5.4 ghz, t a = 25 c, as measured on skyworks solutions? SE5007T-ev1 evaluation board, unless otherwise noted symbol parameter conditions min. typ. max. unit pdr p out detect range - 0 - p 1db dbm vdet 22 detector voltage p out = 22 dbm 0.7 - 0.9 v vdet 16 detector voltage p out = 16 dbm 0.50 - 0.60 v vdet 2 detector voltage p out = 2 dbm 0.25 - 0.35 v pdz out output impedance - - 5 - k ? power detector performance over frequency figure 3: SE5007T power detector characteristic
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 8 of 11 package diagram this package is pb free and rohs compliant. the product is rated msl1. top side bottom side 16 4 9 15 14 13 310 211 112 5678 16 4 5 9 15 6 14 7 13 8 3 10 2 11 1 12 figure 4: SE5007T package diagram
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 9 of 11 recommended land and solder patterns figure 5: SE5007T recommended land and solder pattern package handling information because of its sensitivity to moisture absorption, inst ructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. the SE5007T is capable of withstanding a pb free solder reflow. care must be taken w hen attaching this product, whether it is done manually or in a production solder reflow environment. if the part is manually attached, precaution should be taken to insure that the device is not subjected to temper atures above its rated peak temperature for an extended period of time. for details on both attachment techniques, precautions, an d handling procedures recommended, please refer to: ? ?quad flat no-lead module solder reflow & rework information?, document number qad-00045 ? ?handling, packing, shipping and use of moisture sensitive qfn?, document number qad-00044 caution! class 1a esd sensitive device
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 10 of 11 branding information figure 6: SE5007T branding tape and reel information paramete r v alue devices per reel 3000 reel diameter 13 inches tape width 12 millimeters figure 7: SE5007T-r tape and reel information document change history revision date notes 1.0 jun 24, 2010 created 1.1 jul 2, 2010 corrected control logic table 1.2 jul 7, 2010 expanded frequency range to 4.9ghz to 5.85ghz expanded operating temperature range to -40 to +85 changed vdd supply from 2.5v to 3.3v + 10% 1.3 jul 14, 2010 removed reference to incorrect part number. 1.4 sep 30, 2010 updated rx output return loss (s22) limit 1.5 oct 05, 2010 updated the block diagram 1.6 dec 20, 2010 corrected rx conditions in control logic table sige 5007t lot code
data sheet SE5007T: 5 ghz front end module with power detector skyworks solutions, inc. phone [781] 376-3000 fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com dst-00383 ? rev 2.0 skyworks proprietary information products and product information are subject to change without notice april 3, 2012 11 of 11 revision date notes 1.7 jan 03, 2011 update recommended storage temperature. updated esd rating updated max limit on vcc2 1.8 feb 8, 2011 added 4v operation 1.9 apr 25, 2011 update v enh min spec from 2.8v to 1.6v 2.0 apr 03, 2012 updated with skyw orks logo and disclaimer statement copyright ? 2012 skyworks solutions, inc. all rights reserved. information in this document is provided in connection with skyworks solutions, inc. (?skyworks?) products or services. these m aterials, including the information contained herein, are provided by skyworks as a service to its customers and may be used for informational purposes only by the customer. skyworks as sumes no responsibility for errors or omissions in these materials or the information contained herein. skyworks may change its documentation, products, services, specifications or pro duct descriptions at any time, without notice. skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompati bilities, or other difficulties arising from any future changes. no license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document . skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of skyworks products, information or m aterials, except as may be provided in skyworks terms and conditions of sale. the materials, products and information are provided ?as is? without warranty of any kind, whether express, implied, statutory, or otherwise, including fitness for a particular purpose or use, merchantability, performance, quality or non-infringement of any intellectual property right; all such warranties are hereby expressly disclaimed. skyworks does not warrant the accuracy or completeness of the information, text, gr aphics or other items contained within these materials. skyworks shall not be liable for any damages, including but not limited to any special, indir ect, incidental, statutory, or consequential damages, including without limitation, lost revenues or lost profits that may result from the use of the material s or information, whether or not the recipient of materials has been advised of the possibility of such damage. skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the skyworks products could lead to personal injury, death, physical or environmental damage. skyworks customers using or selling skyworks products for use in such applicat ions do so at their own risk and agree to fully indemnify skyworks for any damages resulting from such improper use or sale. customers are responsible for their products and applications using skyworks products, which may deviate from published specifi cations as a result of design defects, errors, or operation of products outside of published parameters or design specifications. customers should include design and operating s afeguards to minimize these and other risks. skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of skyworks products outside of stated published specifications or parameters. skyworks, the skyworks symbol, and ?breakthrough simplicity? are trademarks or registered trademarks of skyworks solutions, inc ., in the united states and other countries. third- party brands and names are for identification purposes only, and are the property of their respective owners. additional inform ation, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.

▲Up To Search▲

Price & Availability of SE5007T

	To Download SE5007T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .